Flammable Refrigerant Charging: Galileo TP Charger
Bloga dön

Kigali Turns 10 and the U.S. HFC Cap Halves in 2029: Flammable Refrigerant Charging with the Galileo TP Charger

Flammable refrigerant charging after Kigali at 10: the U.S. HFC cap halves in 2029. See how the Galileo TP Charger doses R290, R32 and R600 safely.

Yayımlandı November 17, 2026
Okuma süresi 9 min

Ten years after the Kigali Amendment was agreed in October 2016, the U.S. phasedown of hydrofluorocarbon (HFC) refrigerants is a little over two years from a cut that halves the cap. The Environmental Protection Agency’s (EPA’s) schedule holds total HFC consumption at 60 percent of the national baseline through 2028. In 2029 the cap drops to 30 percent, half of the current level. EPA’s 2027 allowance notice, published in the Federal Register on October 6, 2026, leaves cooling-unit makers two more production years at the current cap before that cut arrives.

In household appliances such as refrigerators, deep freezers and air conditioners, and in residential heat pumps, most of the gases replacing HFCs with a high global warming potential (GWP) are flammable. That makes flammable refrigerant charging a line-design question as well as a chemistry one. A charging station built for nonflammable HFCs wasn’t designed to evacuate, dose and disconnect a combustible gas hundreds of times per shift, and the station is where most of the handling happens.

Kigali at 10: How the HFC Phasedown Works

The Kigali Amendment added HFCs to the Montreal Protocol, the treaty that phased out chlorofluorocarbon (CFC) refrigerants and is phasing out hydrochlorofluorocarbons (HCFCs). EPA describes it as an agreement to cut HFC production and consumption by 80 to 85 percent by 2047. Full implementation is expected to avoid up to half a degree Celsius of warming by the end of the century. The amendment entered into force on January 1, 2019, and the United States ratified it on October 26, 2022.

In the U.S., the phasedown runs under the American Innovation and Manufacturing (AIM) Act of 2020. The law directs EPA to set the following year’s production and consumption allowances by October 1 of each year. Allowances are counted in metric tons of exchange value equivalent (MTEVe), which weighs each HFC by its warming potential. Because of that weighting, a high-GWP blend uses up far more allowance per kilogram than a low-GWP one.

The U.S. HFC Cap Halves in 2029

The step-down is written into federal regulation at 40 CFR 84.7 and measured against a consumption baseline of 302.538.316 MTEVe. Each step applies to both production and consumption:

  • 2022 to 2023: 90 percent of baseline.
  • 2024 to 2028: 60 percent of baseline, or 181.522.990 MTEVe of consumption per year.
  • 2029 to 2033: 30 percent of baseline, or 90.761.495 MTEVe of consumption per year.
  • 2034 to 2035: 20 percent of baseline.
  • 2036 and after: 15 percent of baseline.

The October 2026 notice confirms that 2027 consumption allowances may not exceed 181.522.990 MTEVe, which is the 60 percent level. It also shows the schedule being enforced. Alongside the allocations, EPA gave notice that it had withheld or revoked newly issued 2027 allowances from specific companies as administrative consequences under its regulations.

For a manufacturer, the practical reading is that 2027 and 2028 are the last years at the current cap. Product platforms launching in that window will be built and serviced under an HFC allowance cap half its current size. That’s a strong reason to qualify low-GWP refrigerants and the charging equipment that goes with them before the cut.

The Leading Replacement Refrigerants Are Flammable

Leading low-GWP replacements in cooling-unit manufacturing include hydrocarbons such as propane (R290) and isobutane (R600a), and A2L refrigerants such as R32 and R454B. Under ASHRAE Standard 34, propane and isobutane carry an A3 classification, the higher-flammability class, while A2L is a lower-flammability class. Hydrocarbons aren’t HFCs, so they don’t draw on AIM Act allowances at all. R32 and R454B still do, but their lower warming potential means they use far fewer allowances per kilogram than the high-GWP blends they replace. Commercial refrigeration also uses nonflammable options such as CO₂, so the shift to flammable gases is strongest on appliance and residential heat pump lines.

Flammability raises the stakes on the assembly line as well as in the finished product. A sealed appliance holds its charge in a closed circuit, while the charging station handles the gas in bulk and connects to a new unit every cycle. Without a recovery step, some of the gas left in the filling gun can escape at each disconnect. Hydrocarbon systems also tend to carry small charges, because appliance safety standards limit how much flammable refrigerant a single circuit can hold. At those sizes, a few grams of dosing error becomes a meaningful share of the total charge.

What Flammable Refrigerant Charging Demands from the Station

A charging station for hydrocarbons and R32 has the same core jobs as any charger: evacuate the circuit, verify it and dose the refrigerant. It also has to keep a flammable gas contained at every step. Four requirements separate a line built for that work from one adapted to it, starting before the unit reaches the charger:

  • Ignition control. Components in the mechanical cabinet, including flow meter controls and the vacuum pump, need ratings for explosive atmospheres. In Europe, that equipment falls under the ATEX directive.
  • Tracer gas leak testing before charge. Every charging station evacuates and checks the circuit before refrigerant flows, regardless of the gas being used. With flammable refrigerants, a tracer gas leak test ahead of evacuation and charging stops being an optional quality check and becomes close to a mandatory safety step. Ascential Test & Measurement Systems also builds helium leak detection ve helium recovery systems for that stage of the line.
  • Accurate dosing at small masses. The metering method has to hold tight tolerances on charges of a few dozen grams as well as on large commercial charges.
  • Zero release at disconnect. Gas left in the injector after filling has to be discharged in a controlled way before the coupler unlocks, so no refrigerant escapes into the work area.

Here’s a worked example of why dosing accuracy matters at these sizes. On a 60 g propane charge, a tolerance of plus or minus 0.5 g keeps the charge within about 0.8 percent of target. On a 2.000 g charge, a tolerance of plus or minus 0.5 percent allows about 10 g either way. Metering error grows with the dose, so charging specs, including the one below, quote a fixed gram tolerance for small charges and a percentage for large ones.

Introducing the Galileo TP Charger

The Galileo TP Charger from Ascential Test & Measurement Systems is a next-generation machine for evacuation, leak testing and refrigerant charging, engineered to handle flammable gases. It can be integrated into any cooling-unit assembly line. It covers applications from low production rates with small charge volumes to high production rates with large charge volumes of R290, R32 and R600. It can also charge any kind of HC, CFC, HCFC or HFC refrigerant and mildly flammable A2L blends, so one platform can run legacy and low-GWP gases through a changeover.

Each machine is fitted with one metering device, and the options include:

  • Real-time mass flow meter. A piezoresistive pressure sensor and ATEX controls provide the fastest charging speed under the safest conditions.
  • Dosing cylinder. A volumetric cylinder with a single-effect piston is the option for the most reliable dosing.

With the mass flow meter, rated accuracy is ±0.5 g on hydrocarbon charges under 100 g and ±0.5 percent above 100 g. HFC charges are held to ±1.0 g under 200 g and ±0.5 percent above 200 g, all at a 25 bar refrigerant supply. The mass flow meter also charges hydrocarbons and R32 at up to 90 g/s, or up to 150 g/s with the high-speed kit. The machine can be equipped with an ATEX double-stage rotary vacuum pump at 18 or 28 m³/h, which also checks whether the circuit under test is already filled or evacuated. Final vacuum is below 1×10⁻² Pa.

Each cycle runs as a sequence of programmable phases, and the machine stores up to 1.000 programmable cycles:

  • Automatic locking of the Hansen quick coupler
  • Compressed air verification
  • Dolum tabancası kaçak testi ve ön vakumlama
  • Ön dolum ünitesi testi
  • Ön vakumlama
  • Vacuum rise test
  • Dosing system pressure check
  • Refrigerant filling with a clog test
  • Gas injector discharge, with a zero gas release guarantee
  • Automatic release of the Hansen quick coupler

The last two phases deal directly with the disconnect problem described above. The injector is discharged before the coupler unlocks, and the machine carries a zero gas release guarantee for that step.

A Charging Station Built to Talk to the Line

The TP Charger’s new operator panel is a capacitive 15.6-inch LCD touch screen designed for industrial environments with extreme temperatures and high humidity. Two log-in levels separate operators from maintenance, production and quality managers. The software covers machine parameter setting, refrigerant programming, language selection and barcode management, with 5.000 programmable bar codes as standard and more available on request.

For line integration, the machine supports OPC-UA, RS232/RS485 and Ethernet protocols, with optional Wi-Fi and a dual-screen configuration. It works with external devices including printers, scanners, RFID and NFC, and it can receive cycles from an external system. Service is built around a common embedded platform, with a secure remote connection in accordance with IEC 62443 cybersecurity and remote firmware and software updates. A remote mirrored screen supports diagnostics, programming and maintenance, and the machine includes a built-in spare parts viewer.

How Ascential Test & Measurement Systems Can Help

Ascential Test & Measurement Systems builds evacuation, leak testing and refrigerant charging equipment for cooling-unit assembly lines, and the Galileo TP Charger is the next-generation machine in that range. It’s designed for plants moving to R290, R32 and R600, including lines that will keep charging HFC products for some time alongside them.

If your plan for the 2029 step-down includes a move to hydrocarbons or R32, our engineers can help you match the metering technology, number of dosing systems and vacuum configuration to your charge sizes and production rate. The full data sheet is in the Galileo TP Charger brochure. Speak with our engineers about your refrigerant charging line.

Sık sorulan sorular

What is the Kigali Amendment?

The Kigali Amendment is a 2016 addition to the Montreal Protocol that phases down hydrofluorocarbons, the refrigerants that replaced many ozone-depleting CFCs and HCFCs. EPA describes it as cutting HFC production and consumption by 80 to 85 percent by 2047. It entered into force in 2019, and the United States ratified it in 2022.

When does the U.S. HFC cap drop next?

The next U.S. step-down arrives in 2029, when total HFC production and consumption allowances fall from 60 percent to 30 percent of baseline. Under 40 CFR 84.7, the cap then drops to 20 percent in 2034 and to 15 percent from 2036 onward. EPA sets each year’s allowances by October 1 of the year before.

Why do flammable refrigerants need a different charging machine?

Flammable refrigerants need a charging machine designed to keep the gas contained and away from ignition sources at every step. That means explosion-rated components in the mechanical cabinet, a tracer gas leak test and vacuum checks before charging, accurate dosing on small charges and a controlled discharge of the injector so nothing escapes when the coupler unlocks.

Which refrigerants can the Galileo TP Charger handle?

The Galileo TP Charger is engineered for flammable gases, including R290, R32 and R600, and it can also charge any kind of HC, CFC, HCFC and HFC refrigerant as well as mildly flammable A2L blends. Refrigerant supply pressure runs from 10 to 35 bar, with a maximum working pressure of 38 bar.

How accurate is refrigerant dosing on the TP Charger?

With its mass flow meter, the TP Charger is rated to ±0.5 g on hydrocarbon charges under 100 g and ±0.5 percent above that. HFC charges are held to ±1.0 g under 200 g and ±0.5 percent above, all at a 25 bar refrigerant supply. The programmable dose runs from 5 g to 99,999.9 g, depending on the dosing technology.

Kaynaklar

  1. U.S. EPA: Background on HFCs and the AIM Act
  2. Federal Register: Phasedown of Hydrofluorocarbons, Notice of 2027 Allowance Allocations (October 6, 2026)
  3. eCFR: 40 CFR 84.7, Phasedown schedule
Yazar
  • Valerio PucciSales Director, Galileo
Sentia AI

Sohbet asistanı

SentiaAI

Bugün size nasıl yardımcı olabilirim?

Sohbet kaydınızı indirmek için lütfen aşağıdaki formu doldurun.